How to Set up a Bath Tub: Install an Acrylic Tub and Tub Surround
How to Set up a Bath Tub: Install an Acrylic Tub and Tub Surround
Blog Article
Just how do you feel in relation to A Step-by-Step Guide to Installing a Bathtub?
:max_bytes(150000):strip_icc()/installing-a-tub-or-shower-surround-2718986-hero-40160398595d4544b639b3398cdb247c.jpg)
Setting up a bathtub isn't exactly brain surgery, yet it does need solid plumbing, carpentry, and also sometimes, tiling skills. Replacing an old bathtub with a new one is also a moderately hard project. If the old tub is readily available, the job can move rapidly; if you have to open a wall to remove the old tub and place the brand-new bath tub, the job is a lot harder. In either instance, the job is within a house handyman's skills, although you will need a helper to vacate the old bathtub and also embeded in the new one. See to it you have actually certified yourself for the job and fit trying it. Instead of employing a professional to take over a halfway-completed project, it is far better to take into consideration using one before you begin. Chances are you might require an expert plumber to make tube connections.
This article will certainly assist you set up a new bath tub in your shower room if you have actually currently purchased a new bathtub as well as don't require to alter the plan of your previous water supply pipelines.
Your tools and also material checklist need to make up the following:
Getting ready for the Installation
Firstly, the sustaining framework supplied with the bath needs to be fitted (if called for) according to the maker's directions. Next, fit the faucets or mixer to the tub. When fitting the faucet block, it is necessary to make certain that if the tap features a plastic washing machine, it is fitted between the bath and also the taps. On a plastic bath, it is additionally practical to fit a supporting plate under the taps unit to stop stress on the bathtub.
Fit the adaptable tap adapters to the bottom of both taps making use of 2 nuts as well as olives (sometimes provided with the tub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink electrical outlet hole, and afterwards pass the electrical outlet through the hole in the bath. Make use of the nut provided by the producer to fit the plug-hole. Examine the plug-hole electrical outlet for an inlet on the side for the overflow pipeline.
Next, fit completion of the adaptable overflow pipe to the overflow electrical outlet. After that, screw the pipeline to the overflow face which must be fitted inside the bath. Make sure you make use of all of the supplied washing machines.
Link the catch to the bottom of the waste electrical outlet on the bathtub by winding the string of the waste outlet with silicone mastic or PTFE tape, and screw on the catch to the electrical outlet. Link the bottom of the overflow tube in a similar manner.The bathroom must now be ready to be suited its last setting.
Removing Old Touches
If you require to change old taps with brand-new ones as a part of your setup, then the first thing you ought to do is detach the water supply. After doing so, activate the taps to drain pipes any type of water remaining in the system. The procedure of removing the existing faucets can be quite problematic because of the restricted gain access to that is usually the case.
Make use of a basin wrench (crowsfoot spanner) or a tap device to undo the nut that attaches the supply pipelines to the taps. Have a towel ready for the continuing to be water that will certainly come from the pipelines. Once the supply pipelines have been gotten rid of, utilize the same device to loosen the nut that holds the faucets onto the bath/basin. You will require to stop the solitary taps from transforming during this procedure. When the faucets have been gotten rid of, the holes in the bath/basin will need to be cleaned up of any type of old securing compound.
Prior to proceeding to fit the brand-new taps, contrast the pipe links on the old taps to the brand-new taps. If the old taps are longer than the brand-new taps, after that a shank adapter is required for the brand-new faucets to fit.
Setting up the Bath tub
Using both wooden boards under its feet, put the bath tub in the needed placement. The wooden boards are practical in evenly spreading the weight of the bath tub over the area of the boards rather than concentrating all the weight onto four tiny points.
The next objective is to ensure that the tub is leveled all round. This can be attained by checking the level and also adjusting the feet on the tub till the spirit level checks out degree.
To mount taps, fit the bottom of the outermost flexible tap port to the ideal supply pipe by making a compression join; after that do the very same for the other tap.
Turn on the water and inspect all joints as well as brand-new pipework for leakages and tighten them if required. Load the bath tub and also inspect the overflow electrical outlet and also the regular outlet for leaks.
Lastly, take care of the bath paneling as explained in the maker's user's manual. Tiling and also sealing around the bathtub ought to wait up until the tub has actually been made use of at the very least when as this will settle it into its final setting.
Suitable New Touches
If the tails of the brand-new faucets are plastic, after that you will certainly require a plastic adapter to avoid damages to the thread. One end of the adapter fits on the plastic tail of the tap and the other end supplies a link to the current supply pipes.
If you need to fit a monobloc, then you will certainly call for reducing couplers, which connects the 10mm pipe of the monobloc to the common 15mm supply pipeline.
Next off, place the tap in the mounting hole in the bath/basin guaranteeing that the washing machines remain in area in between the faucet and also the sink. Secure the tap in place with the producer supplied backnut. As soon as the faucet is safely in position, the supply pipelines can be linked to the tails of the taps. The taps can either be connected by using corrugated copper piping or with normal tap connectors. The former type should be connected to the tap ends first, tightening up just by hand. The supply pipes can later be connected to the various other end. Tighten up both ends with a spanner after both ends have been connected.
Tiling Around the Bath tub
In the location where the bathroom meets the tile, it is required to seal the joins with a silicone rubber caulking. This is essential as the fitting can move sufficient to fracture an inflexible seal, creating the water to permeate the wall between the bathroom as well as the tiling, resulting in problems with dampness and also feasible leakages to the ceiling below.
You can choose from a variety of coloured sealers to assimilate your fixtures and installations. They are marketed in tubes as well as cartridges, and are capable of securing spaces as much as a width of 3mm (1/8 inch). If you have a bigger space to fill up, you can fill it with spins of drenched newspaper or soft rope. Remember to constantly fill up the bathtub with water prior to securing, to allow for the activity experienced when the bathtub is in use. The sealer can break fairly very early if you do not take into consideration this movement prior to sealing.
Alternatively, ceramic coving or quadrant floor tiles can be utilized to edge the bathroom or shower tray. Plastic strips of coving, which are easy to use as well as cut to dimension, are likewise conveniently offered on the market. It is suggested to fit the ceramic tiles using waterproof or water resistant adhesive as well as grout.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
As an enthusiastic reader on Installing A Bathtub, I assumed sharing that portion was really useful. Sharing is good. You never know, you could be helping someone out. Thank you for going through it.
Request An Appointment
Report this page